Epson WorkForce 40 Series Guida di Installazione

Network Installation Guide

10 Wireless Network Installation9. Select Wireless (remove Ethernet cable when prompted) as the network communication type, then click Next.10. Select

Wireless Network Installation 1111. If your wireless network doesn’t have security enabled, continue with step 12.If your wireless network has securit

12 Wireless Network Installation12. When you see this screen, click Next to configure the printer’s IP address automatically (recommended).Note: To co

Wireless Network Installation 1314. When you see the Switch to Wireless Connection screen, disconnect the Ethernet network cable from your printer.15.

14 Wireless Network InstallationWait while your computer confirms the network connection. Note: It may take a while for the printer to connect to the

Wired (Ethernet) Installation 15 Wired (Ethernet) InstallationFollow the steps in this section to connect the printer to your network with an Ethernet

16 Wired (Ethernet) InstallationInstall SoftwareBefore starting, make sure the printer is not connected with a USB cable. Only an Ethernet cable shoul

Wired (Ethernet) Installation 174. When you see this screen, select Install driver for network connection and click Next.5. Follow the instructions on

18 Wired (Ethernet) InstallationConfigure Network Settings1. Make sure that the printer is turned on.2. When you see the FireWall Warning screen, clic

Wired (Ethernet) Installation 194. Select Method 1: Connect via a router/access point (RECOMMENDED). Important: Do not select Method 2: Connect direct

2 Before You BeginBefore You BeginMake sure you installed ink cartridges and loaded paper as described on theStart Here sheet. Then follow the instruc

20 Wired (Ethernet) Installation6. Select the printer you want to configure, then click Next.Note: It may take up to 90 seconds for your computer to f

Wired (Ethernet) Installation 218. When you see this screen, click Next to configure the IP address automatically (recommended).Note: To configure the

22 Wired (Ethernet) Installation10. When you see the Network Connection Successful screen, click Next.Note: Do not disconnect the Ethernet cable from

Install on Additional Computers 23Install on Additional ComputersFollow the steps in this section to install the printer software on each additional c

24 Install on Additional Computers4. When you see this screen, select Install driver for network connection and click Next.5. Follow the instructions

Install on Additional Computers 258. When you see the FireWall Warning screen, click Next.9. If you see a firewall alert message click Unblock or Allo

26 Install on Additional Computers10. Select the printer you want to install, then click Next.Note: It may take up to 90 seconds for your computer to

Finish the Installation 27Finish the InstallationFollow the steps for your operating system: “Windows” below “Mac OS X” on page 28Windows1. Follow t

28 Finish the InstallationMac OS X1. Follow the on-screen instructions. After making a successful network connection, click Next. When you see this sc

Finish the Installation 294. Click Next.5. Follow the on-screen instructions to finish installing software and print a test page.When installation is

Wireless Network Installation 3 Wireless Network InstallationTo connect your printer wirelessly, you need to know the name (SSID) of your wireless net

30 TroubleshootingTroubleshootingIf you have problems setting up or using your product on a network, check these sections for help:“Setup Problems” be

Troubleshooting 31 Make sure you entered the correct WEP key or WPA passphrase for your wireless network. WEP keys are either ASCII or hexadecimal. I

32 TroubleshootingPrinting ProblemsCannot print over the network Print a network status sheet (see page 34) and verify that the network settings are

Troubleshooting 33A dial-up connection dialog box appears when printing with EpsonNet PrintIf you use a dial-up connection for Internet access, you wi

34 TroubleshootingUsing the Network ButtonsYou can use the network buttons on the printer’s control panel for the following functions: Clear a wirele

Copyright Notice 35Copyright NoticeAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in

CPD-25742R1Printed in XXXXXX

4 Wireless Network Installation2. Connect the other end to any available LAN port on your router, access point, or hub.If you don’t have access to an

Wireless Network Installation 5Install SoftwareBefore starting, make sure the printer is not connected with a USB cable. Only an Ethernet cable should

6 Wireless Network Installation4. When you see this screen, select Install driver for network connection and click Next.5. Follow the on-screen instru

Wireless Network Installation 7Configure Network Settings1. Make sure that the printer is turned on.2. When you see the FireWall Warning screen, click

8 Wireless Network Installation4. Do one of the following: If the printer is connected to your router, access point, or hub, select Method 1: Connect

Wireless Network Installation 9Note: Make sure that you allow network access for Epson EasyInstall. In Windows, verify that the publisher is SEIKO EPS